PIC16F87T-E/ML【PDF 195/200 页】IC MCU FLASH 4KX14 EEPROM 28QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3882

191页 192页 193页 194页 [195页]196页 197页 198页 199页

8008H–AVR–04/11

ATtiny48/88

located in the Timer/Counter Control Register B (TCCR1B). For details on clock sources and

prescaler, see “Timer/Counter0 and Timer/Counter1 Prescalers” on page 117.

12.5

Counter Unit

The main part of the 16-bit Timer/Counter is the programmable 16-bit bi-directional counter unit.

Figure 12-2 shows a block diagram of the counter and its surroundings.

Figure 12-2. Counter Unit Block Diagram

Signal description (internal signals):

Count

Increment or decrement TCNT1 by 1.

Direction

Select between increment and decrement.

Clear

Clear TCNT1 (set all bits to zero).

clk

Timer/Counter clock.

TOP

Signalize that TCNT1 has reached maximum value.

BOTTOM

Signalize that TCNT1 has reached minimum value (zero).

The 16-bit counter is mapped into two 8-bit I/O memory locations: Counter High (TCNT1H) con-

taining the upper eight bits of the counter, and Counter Low (TCNT1L) containing the lower eight

bits. The TCNT1H Register can only be indirectly accessed by the CPU. When the CPU does an

access to the TCNT1H I/O location, the CPU accesses the high byte temporary register (TEMP).

The temporary register is updated with the TCNT1H value when the TCNT1L is read, and

TCNT1H is updated with the temporary register value when TCNT1L is written. This allows the

CPU to read or write the entire 16-bit counter value within one clock cycle via the 8-bit data bus.

It is important to notice that there are special cases of writing to the TCNT1 Register when the

counter is counting that will give unpredictable results. The special cases are described in the

sections where they are of importance.

Depending on the mode of operation used, the counter is cleared, incremented, or decremented

at each timer clock (clk

T1). The clkT1 can be generated from an external or internal clock source,

selected by the Clock Select bits (CS1[2:0]). When no clock source is selected (CS1[2:0] = 0)

the timer is stopped. However, the TCNT1 value can be accessed by the CPU, independent of

whether clk

T1 is present or not. A CPU write overrides (has priority over) all counter clear or

count operations.

The counting sequence is determined by the setting of the Waveform Generation mode bits

(WGM1[3:0]) located in the Timer/Counter Control Registers A and B (TCCR1A and TCCR1B).

There are close connections between how the counter behaves (counts) and how waveforms

TEMP (8-bit)

DATA BUS (8-bit)

TCNTn (16-bit Counter)

TCNTnH (8-bit)

TCNTnL (8-bit)

Control Logic

Count

Clear

Direction

TOVn

(Int.Req.)

Clock Select

TOP

BOTTOM

Edge

Detector

( From Prescaler )

clk

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式